Finally, a solution that allows you to safely increase without the risk of damaging your front axles. as you add GT3 shims to your front Porsche 996/997 turbo lower control arms, you move the cv joints beyond their safe range of motion, risking failure and expensive damage. These 10mm thick precision spacers, used with 16mm of lca shims will provide an additional -1.7 deg. Of camber, while maintaining the factory cv joint and axle relationship. the spacer design features a concentric lip that positively and accurately locates it to the cv joint for perfect balance and no vibration. Each kit includes two spacers and all the needed hardware in high class 10.9 grad

If your outer tie rods are worn, you will experience sloppy steering response and knocking / creaking sounds. Your outer tie rods keep the steering centered, so failure can be dangerous and can seriously affect steering control. After replacing the tie rods, you will experience tighter, more precise feedback without noise. Tie rod consists of: 1 qty. Tie rod 1 qty. Hexagon nut (m14 x 1.5) 1 qty. Inner axial joint 1 qty. Lock nut 1 qty. Dust bellows / boot we recommend replacing the right and left side tie rods at the same time. Sold individually. 2 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stoc...(choose a part on the right to read more)

We are committed to Porsche cars and are very happy to release an inner tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. We also suggest replacing your outer tie rods, part # 96434703200 (qty. 2 are needed) and now is also a good time to replace your worn out inner tie rod dust bellows, part # 96434719103. Please note: this is not for the ...(choose a part on the right to read more)

Cv boots are inexpensive, so replace them before they crack and cause an expensive cv joint failure. This kit does one side, two needed per axle.

General Fitment

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

View/Change Diagram

911 1984-86 - Rear Axle

911 1987-89 - Rear Axle

Enhance steering precision and steering feedback by simply replacing your original tie rods. Turbo tie rods use a spherical inner joint instead of soft rubber bushings. They offer quicker steering response, more sensitivity and more precision. These are standard length we highly recommend them for lowered vehicles with bump steer kits like part # FVD34791100 or FVD347911930 . We also offer turbo tie rods in longer lengths for other applications, check part # FVD34791180r and FVD34791181ry this kit is manufactured in Germany by an OEM supplier, made from high carbon steel and 7075 t6 aluminum. Kit includes: 2 qty. Outer tie rods 2 qty. Inner tie rods 2 qty. Spacing washers 2 qty. Boots 2 qty. Castle nuts 2 qty. ...(choose a part on the right to read more)

Panamera models with optional air suspension utilize four sensors to control the ride height. This is accomplished via the use of a small linkage or link which connects the sensor to the suspension. As the car is raised or lowered, the link moves the sensor up or down sending a signal to the computer telling it how high the car is. When you replace the non-adjustable factory link with this adjustable design, the output of the sensor makes the computer believe that the car is higher than it is. So, the computer will lower the ride height. The simplicity of this setup is that it retains full functionality of the factory system. Be warned, all adjustable lowering links are not the same! These links are machined al...(choose a part on the right to read more)

General Fitment

Redline oil: red line formulates fully-synthetic oils and chemically-advanced additives using the world’s finest base stocks. Rather than cutting costs by blending in petroleum products, red line's motor oils and gear oils use superior ester base stocks that provide extreme stability at high temperatures and superior film strength at lower viscosities where more power can be produced.

Volume: 14oz tube redline cv-2 grease withstands extreme temperature and pressure in wheel bearings, u-joints, and high-angle cv joints

General Fitment

Es gibt 2 verschiedene versionen fur 356a und fur 356 b+c: der am konus zur verschraubung mit der kronenmutter sind unterschiedlich bei den beiden modellen - bis 1957 waren es am konus zur mutter 10,7mm -schmalste stelle-/12,2mm -breiteste stelle- - seit 1958 sind es 12,6mm/14,2mm.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.